精选 TI 参考设计

查找采用最佳 TI 技术的参考设计来解决您的系统级难题

应用范围

产品

其它资源

描述

The TIDA-01002 reference design provides uncompressed, 1 megapixel, HDR, YUV422 video for use in ADAS and infotainment systems. It uses TIs FPD-Link III SerDes technology and the ON Semiconductor® AS0140AT CMOS Imager to transmit video data, bidirectional control signals and power all over a (...)

主要特色

  • Module outputs YUV422 720p up to 30fps
  • Space optimized design fits on a single PCB 20x20mm
  • Single Rosenberger Fakra coax connector for digital video, power, control and diagnostics

Updated: 21 NOV 2017

描述

This reference design provides protection and diagnostics for antenna modules for use in automotive infotainment and navigation systems. This design is an alternate solution for antenna low-dropout linear regulators (LDOs) for the purpose of achieving lower ohmic drop (IR) while meeting the (...)

主要特色

  • Open Load Detection at 10 mA (Typical)
  • Selectable Overcurrent Detection at 300 mA, 600 mA, 900 mA, 1.2 A
  • Shutoff in 1 μs (Typical) to Short-to-Battery Fault
  • Fast Response of 200 ns (Typical) to Short-to-Ground Fault
  • Low IR Drop With TPS25940-Q1 (42 mΩ RON)

描述

This ethernet brick reference design provides a simplified solution that eliminates the need to have multiple boards for copper or fiber interface. It uses a small form factor, low power 10/100 Mbps ethernet transceiver to reduce board size for a cost optimized and scalable solution with reduced (...)

主要特色

  • DP83822 ethernet PHY with fiber (100BASE-FX ) or twisted-pair (copper - 100BASETX and 10BASE-Te) interface  
  • Provision to configure analog and IO supply voltage levels separately based on application
  • Programmable LED support for link and activity
  • Meets EN55011 Class-A radiated emission requirements, and (...)

Updated: 20 NOV 2017

描述

In HVAC (heating, ventilation, and air conditioning) HMI (human machine interface) the displays and buttons are illuminated with many of LEDs. The drive circuit for these LEDs are traditionally realized in a discreet way so that an MCU drives external low side BJTs that sink current, limited by (...)

主要特色

  • Configurable 16-channel LED driver
  • Independent control of each channel
  • LED dimming adjustment to the ambient light intensity
  • Constant current control

描述

The TIDEP0076 3D machine vision design describes an embedded 3D scanner based on the structured light principle. A digital camera along with a Sitara™ AM57xx processor System on Chip (SoC)  is used to capture reflected light patterns from a DLP4500-based projector. Subsquent processing of (...)

主要特色

  • Demonstration of 3D machine vision inspection with DLP® technology-based structured light techniques.
  • Fully embedded 3D machine vision system based on Sitara AM57xx SoC and DLP Lightcrater™ 4500. No PC required.
  • Provides 3D object point cloud
  • Demonstrates generation and rendering of 3D point clouds (...)

Updated: 20 NOV 2017

描述

This reference design is an isolated high-side current sensing design for a smart combiner box in a grounded or ungrounded system. The current sensing topology enables multichannel, sub ±1% error, isolated current sensing for high-voltage systems up to 1200-VDC, limited by the DC/DC transformer.

主要特色

  • Isolated high-side current sensing of multiple photovoltaic strings
  • Capable of monitoring current within 1% full scale accuracy
  • Support 1200V isolated current sensing via I2C in smart combiner boxes
  • Option to connect additional INA260 devices to I2C bus

Updated: 17 NOV 2017

描述

This compact reference design is a typical PoE application, supplying 10W at 5.3V from Ethernet power. Data filter, external auxiliary input and EMI filter are all on board. The synchronous rectification improves the efficiency, important at only 5.3V output voltage.

主要特色

  • Good efficiency for this class of power, 91% @ 48Vin (PoE input), full load
  • Compact solution: without connectors and data filter, only 40mm x 60mm
  • The board can be configured to work with and without synchronous rectification

Design Parameters

 
 
Vin (V) (Min)
Vin (V) (Min)
Vin (V) (Max)
Vin (V) (Max)
Vout (V) (Nom)
Vout (V) (Nom)
Iout (A) (Max)
Iout (A) (Max)
Output Power (W)
Output Power (W)
隔离/非隔离
隔离/非隔离
输入类型
输入类型
拓扑
拓扑
Designed for
Designed for
PMP30290.1
(Output
Voltage1)
42.5 57 5.3 1.9 10.07 Isolated DC Flyback- Synchronous

Updated: 17 NOV 2017

描述

The PMP30189 reference design is based on the LM5117 sync buck converter; it supplies 24V @ 11A and it is protected against overcurrent at 13.9A. The internal bias can be supplied internally by means of internal linear regulator, or externally by BJT and Zener diode, thus reducing power (...)

主要特色

  • High power (264W), high-efficiency (98.4% @ 27 Vin) sync-buck
  • Precision output overcurrent and overvoltage protection
  • Selectable latching/non-latching overcurrent protection
  • Tracking input + switching frequency selection

Design Parameters

 
 
Vin (V) (Min)
Vin (V) (Min)
Vin (V) (Max)
Vin (V) (Max)
Vout (V) (Nom)
Vout (V) (Nom)
Iout (A) (Max)
Iout (A) (Max)
Output Power (W)
Output Power (W)
隔离/非隔离
隔离/非隔离
输入类型
输入类型
拓扑
拓扑
Designed for
Designed for
PMP30189.1
(Output
Voltage1)
27 29 24 11 264 Non-Isolated DC Buck- Synchronous

描述

这是一种增量式旋转编码器,使用非接触式磁性感应来检测旋转速度和方向。两个霍尔效应传感器可测量 66 极环形磁体并输出两个正交信号。此汽车级解决方案具有低成本特点,由于使用固态检测,不受物理磨损、污垢、腐蚀和射频噪声的影响,因此是用于取代常规机械接触式编码器的高可靠性产品。

主要特色

  • 极其简单、可靠且成本低廉
  • 与机械编码器模块相比具有更高的设计灵活性和 ESD 抗扰度
  • 66 极磁体提供每转 360° 高达 132 次检测(每 2.7° 检测一次)
  • 大于 20kHz 的霍尔效应传感器带宽可提供 15µs 的低延迟
  • 数字感应和数字信号提供噪声抗扰性
  • 通过 AEC-Q100 汽车认证

Updated: 17 NOV 2017

描述

This circuit reference design is realized in Cuk Topology. The output voltage is -12V / -15V. The output current of 200mA is possible over an input voltage range of 10V to 60V  (even with a low input voltage of 6V 140mA output current is possible).  The perfect switching behavior of the (...)

主要特色

  • Cost effective (LM5001, TLV271)
  • Suitable for audio
  • Despite Cuk topology, excellent dynamic behavior
  • Lowest ripple at input and output
  • Transient response on a 50% load step is only 1%
  • The circuit reference design is built and tested

Design Parameters

 
 
Vin (V) (Min)
Vin (V) (Min)
Vin (V) (Max)
Vin (V) (Max)
Vout (V) (Nom)
Vout (V) (Nom)
Iout (A) (Max)
Iout (A) (Max)
Output Power (W)
Output Power (W)
隔离/非隔离
隔离/非隔离
输入类型
输入类型
拓扑
拓扑
Designed for
Designed for
PMP30373.1
(Output
Voltage1)
10 60 -12 .2 2.4 Non-Isolated DC Other
查看TI 设计重要通告,包括使用授权,知识产权事宜及免责声明。